SIEMENS
9/7
Siemens D 41 · 2017
Engineering Tools
SINAMICS Drive Control Chart (SINAMICS DCC)
9
■
Overview
SINAMICS Drive Control Chart (SINAMICS DCC) expands the
scope of device functions by means of freely available closed-
loop control, arithmetic and logic blocks and offers a means by
which technological functions can be graphically configured in
the SINAMICS drive system. SINAMICS DCC is a part of the
Advanced Technology Function and is installed as an add-on to
the STARTER commissioning tool.
SINAMICS DCC provides users with greater integral scope to
adapt these systems to the specific functions of their machines.
SINAMICS DCC does not limit the number of functions that can
be used. The number of functions is limited only by the perfor-
mance capability of the Control Unit.
SINAMICS DCC is available for the following SINAMICS drive
systems:
•
SINAMICS G130 and SINAMICS G150
•
SINAMICS S120 and SINAMICS S150
•
SINAMICS DCM and SINAMICS DCP
•
SINAMICS GM150 and SINAMICS SM150
•
SINAMICS GL150 and SINAMICS SL150
The user-friendly DCC editor enables easy graphics-based con-
figuration, allows control loop structures to be clearly repre-
sented and provides a high degree of reusability of diagrams
that have already been created.
The open-loop and closed-loop control functions are defined by
using multi-instance-capable blocks (Drive Control Blocks
(DCBs)) from a library (DCB library) that are selected and graph-
ically linked with one another by dragging and dropping. Test
and diagnostic functions allow the program behavior to be veri-
fied and, in the case of a fault, the cause identified.
Two types of DCB library are available, i.e. DCB Standard and
DCB Extension. The DCB Standard library supplied with
SINAMICS DCC contains a large selection of closed-loop,
arithmetic and logic blocks, as well as comprehensive open-
loop and closed-loop control functions.
For logically combining, evaluating and acquiring binary sig-
nals, all commonly used logic functions are available for selec-
tion (AND, XOR, on/off delay, RS flipflop, counter, etc.). A wide
range of arithmetic functions, such as absolute value generation,
dividers and minimum/maximum evaluation are available to
monitor and evaluate numerical quantities. In addition to the
closed-loop drive control, axial winder functions, PI controllers,
ramp-function generators or wobble generators are simple to
configure.
SINAMICS DCC also offers the DCB Extension library from firm-
ware version V4.6 and higher. This contains an extended range
of blocks that is used as an additional, independent library in the
DCC Editor. It includes the GMC and Math Extended library.
The GMC contains Motion Control blocks (GEAR, POSMC,
CAMD, etc.).
With Math Extended, supplementary mathematical and logical
function blocks (ASIN, ACOS, ATAN, LOG, etc.) are made
available.
These libraries are ready for downloading along with application
examples from the Siemens Application Support website.
Further information can be found on the Internet at
/sinamics-applications
As well as the option of using the libraries made available by
DCB Extension, DCB Extension proprietary libraries can also be
created with custom-programmed blocks. These blocks and
libraries are programmed with the separate SINAMICS DCB
Studio development tool in the C/C++ high-level language and
can be used as your own DCB Extension Library in the DCC
editor. Use of these blocks as DCB extensions requires a runtime
license.
The separate SINAMICS DCB Studio development tool is re-
quired for programming the blocks and generating the library as
a DCB Extension.
Minimum hardware and software requirements
See STARTER commissioning tool.
■
Selection and ordering data
SINAMICS DCC comprises the graphical configuring tool (DCC
Editor) and the DCB standard library. SINAMICS DCC is installed
as an add-on to the STARTER commissioning tool.
The necessary engineering license for each PC (floating) for
SINAMICS DCC is acquired at the same time the order is placed.
No runtime license is required for the DCB standard library in-
cluded in the scope of supply.
Existing licenses for SINAMICS DCC V2.1 and V2.2 SP1 and
V2.3 SPx are also valid for SINAMICS DCC V2.4 SP1.
An upgrade version including an engineering license for
applications with STARTER V4.5 SP1 is available for existing
SINAMICS DCC V2.0 SPx.
Description
Article No.
SINAMICS DCC V2.4 SP1
for STARTER V4.5 SP1
Graphic configuring with SINAMICS DCC
DCC Editor + DCB standard library
• Single-user engineering license,
with data carrier
6AU1810-1HA24-1XA0
• Upgrade engineering license,
with data carrier
6AU1810-1HA24-1XE0
DCB Extension license
Runtime license for license upgrading
with firmware version V4.6 or later
(can also be ordered in conjunction with
the CompactFlash card,
see Compact-
Flash card for CU310-2 and CU320-2
Control Units
)
6SL3077-0AA00-0AB0
SINAMICS DCB Studio V1.2
Development tool for programming
blocks and DCB Extension libraries as
from Firmware V4.6
On request
© Siemens AG 2017