SIEMENS
7/40
Siemens IK PI · 2015
Industrial Remote Communication
TeleControl Professional for the control center
WinCC/TeleControl
7
■
Function
Special characteristics of DNP3 communication
•
Change-driven data transmission
- Change-driven transmission of process data between RTU
and control center
- Signaling of RTU, control center or connection failure
- Automatic data updating for all communication partners
involved following troubleshooting and following the startup
of the RTU or control center
•
Chronological processing of process data
- Time tagging of all data frames at the place of origin allows
process data to be archived by the process control system
in the correct chronological order
- The time of the DNP3 stations in the WAN can be synchro-
nized via SIMATIC WinCC (including summertime/wintertime
switchover)
•
Local data storage
- The TIM communication module can temporarily store
(for several hours or even days) message frames should the
connection or the communication partner fail
- Intermediate storage of message frames of lower priority in
the case of priority-controlled data transmission (with dial-up
networks or quantity-dependent data transmission costs)
Operating modes
The DNP3 telecontrol protocol supports the following operating
modes:
• Polling
•
Polling with time slot procedure
•
Multi-master polling with time slot procedure
•
Spontaneous mode in dial-up networks
•
Spontaneous mode in the TCP/IP-based WAN
■
Integration
Integration of WinCC/TeleControl for WinCC V7.0 SP2 into the
WinCC SCADA system offers particular advantages for the water
and waste water sectors, as well as oil and gas sectors,
especially in the case of the following types of plant:
•
Freshwater treatment and distribution
•
Wastewater treatment plants
•
Oil and gas pipelines and water pipes
•
Oil and gas drilling fields and the associated treatment plants
In these types of plant, remote outstations such as pumping
stations, valve stations or automated stations for wellheads must
be integrated.
Through the support of communication protocols for RTUs such
as SINAUT ST7, WinCC/TeleControl for WinCC V7.0 SP2
supports the following advanced communication concepts:
•
Reduction in the transferred data volume by means of event-
controlled communication mechanisms for alarm and
measured value information.
•
Time-synchronization of RTUs and correct time stamping of all
data in the RTU.
•
Tolerance of lower bandwidth, high latency or lack of reliability
of communication lines
•
Prevention of data loss due to communications failure through
data backup in the RTU
•
Support of communication media with serial interface
(dedicated lines, dial-up connections over analog telephone
lines and ISDN lines), various radio devices (standard, spread
spectrum modulation), microwave and GSM
•
Support for TCP/IP-based WANs (Wide Area Networks) such
as DSL, GPRS or Ethernet radio networks
•
Support for redundant communication connections
•
Expanded communication diagnostics functions for RTU
communication links
•
Remote programming of RTUs
•
Support for different communication topologies – Point-to-
point, multidrop (multistation mode) and hierarchic network
structures
•
High quality server redundancy scheme without data loss in
the case of server failure
Through the support of communication protocols for RTUs such
as IEC 60870-5 and DNP3, SIMATIC TeleControl for WinCC V7.0
SP2 supports the following advanced communication concepts:
•
Reduction in the transferred data volume by means of event-
controlled communication mechanisms for alarm and
measured value information.
•
Time synchronization of RTUs and correct time stamping of all
data in the RTU.
•
Tolerance of lower bandwidth, high latency or lack of reliability
of communication lines
•
Prevention of data loss due to communications failure through
data backup in the RTU (not all non-Siemens RTUs support
this)
•
Support of communication media with serial interface
(dedicated lines, dial-up connections over analog telephone
lines and ISDN lines), various radio devices (standard, spread
spectrum modulation), microwave and GSM
•
Support for TCP/IP-based WANs (Wide Area Networks) such
as DSL, GPRS or Ethernet radio networks
•
Support for redundant communication connections
•
Expanded communication diagnostics functions for RTU
communication links
•
Remote programming of RTUs
•
Support for different communication topologies – Point-to-
point, multidrop (multistation mode) and hierarchic network
structures
•
High quality server redundancy scheme without data loss in
the case of server failure
© Siemens AG 2014