SIEMENS
6/6
Siemens D 31 N · March 2016
6
■
Design
SINAMICS G110M distributed inverters
0.37 kW to 4 kW (0.5 hp to 5 hp)
SINAMICS G110M distributed frequency inverters
PC inverter connection kit (mini USB interface cable) for
communication with a PC
For controlling and commissioning an inverter directly from a PC
if the appropriate software (STARTER commissioning tool V4.3
and higher or SINAMICS Startdrive V13 and higher) has been
installed.
Internal braking resistors
Excess energy in the DC link is dissipated in the internal braking
resistor.
24 V DC power supply
A 24 V DC power supply is also available for SINAMICS G110M.
This is mounted directly on the inverter and supplies the device
with 24 V DC, so there is no need to connect an external 24 V DC
power supply.
Wall mounting kit
If a SINAMICS G110M distributed inverter should not or cannot
be mounted on the motor, a wall mounting kit is available. With
the wall mounting kit SINAMICS G110M can be mounted close
to the motor – according to the conditions of the plant.
Repair switch
For SINAMICS G110M a repair switch is available. This is
mounted directly on the inverter and separates
SINAMICS G110M on the input side from the 400 V line supply.
Connecting cable for the Control Units
Flexible plug-in cables to transfer data between the Industrial
Ethernet stations or PROFIBUS stations, as well as to supply
power to the Control Unit.
Connecting cable for the Power Modules
Connector sets and pre-assembled cables for the line supply
can be ordered as accessories.
Installation kits
Different installation kits can be ordered as accessories for the
Control Units with plug-in connections and Control Units with
cable gland connections.
These kits include covers or cable glands for protecting or con-
necting the 400 V 3 AC supply, the 24 V DC supply and the
mechanical motor brake.
Spare Parts Kit
A Spare Parts Kit is available which comprises small parts such
as seals, caps and screws.
■
Configuration
The following electronic configuring aids and engineering tools
are available for the SINAMICS G110M distributed inverters:
Drive Technology Configurator (DT Configurator)
within the CA 01
The interactive catalog CA 01 – the offline Industry Mall of
Siemens on DVD-ROM – contains over 100 000 products with
approximately 5 million possible drive system product variants.
The Drive Technology Configurator (DT Configurator) has been
developed to facilitate selection of the correct motor and/or
inverter from the wide spectrum of drives. It is integrated as a
selection tool in Catalog CA 01.
Online DT Configurator
In addition, the DT Configurator can be used on the Internet with-
out requiring any installation. The DT Configurator can be found
in the Siemens Industry Mall at the following address:
/dt-configurator
SIZER for Siemens Drives engineering tool
The SIZER for Siemens Drives engineering tool makes it easy to
engineer the SINAMICS and MICROMASTER 4 drive families.
It provides support when selecting the hardware and firmware
components necessary to implement a drive task. SIZER for
Siemens Drives is designed to support configuring of the entire
drive system.
You can find further information on the SIZER for Siemens Drives
engineering tool in the chapter Engineering tools.
The SIZER for Siemens Drives engineering tool is available free
on the Internet at
/sizer
STARTER commissioning tool
The STARTER commissioning tool allows menu-prompted
commissioning, optimization and diagnostics. Apart from for
SINAMICS drives, STARTER is also suitable for
MICROMASTER 4 devices; for SINAMICS G110M from
STARTER V4.3 SP3 and higher
1)
.
You can find further information about the STARTER commission-
ing tool in the chapter Engineering tools.
Additional information about the STARTER commissioning tool is
available on the Internet at
/starter
SINAMICS Startdrive commissioning tool (V13 and higher)
SINAMICS Startdrive is a tool for configuring, commissioning,
and diagnosing the SINAMICS family of drives and is integrated
into the TIA Portal. SINAMICS Startdrive can be used to imple-
ment drive tasks with the SINAMICS G110M
2)
,
SINAMICS G120, SINAMICS G120C, SINAMICS G120D and
SINAMICS G120P inverter series. The commissioning tool has
been optimized with regard to user friendliness and consistent
use of the TIA Portal benefits of a common working environment
for PLC, HMI and drives.
You can find further information on the SINAMICS Startdrive
commissioning tool in the chapter Engineering tools.
The SINAMICS Startdrive commissioning tool is available free on
the Internet at
/startdrive
Drive ES engineering system
Drive ES is the engineering system that can be used to integrate
the communication, configuration and data management func-
tions of Siemens drive technology into the SIMATIC automation
world easily, efficiently and cost-effectively. Two software pack-
ages are available for SINAMICS – Drive ES Basic and
Drive ES PCS.
You can find further information about the Drive ES engineering
system in the chapter Engineering tools.
Additional information about the Drive ES engineering system is
available on the Internet at
/drive-es
1)
SINAMICS G110M with AS-Interface is available from STARTER V4.4 SP1.
2)
SINAMICS G110M with AS-Interface is available from
SINAMICS Startdrive V 13 SP1.
© Siemens AG 2016