SIEMENS
9/27
Siemens MD 50.1 · 2015
Motor integrated frequency inverter SINAMICS G110M
0.37 kW to 4 kW
Supplementary system components
9
■
Accessories
Memory cards
Fig. 9/25
SINAMICS memory card (SD card)
The parameter settings for an inverter can be stored on the
SINAMICS SD card. When service is required, e.g. after the
inverter has been replaced and the data has been downloaded
from the memory card, the system is immediately ready for use
again.
•
Parameter settings can be written from the memory card to the
inverter or saved from the inverter to the memory card.
•
Up to 100 parameter sets can be stored.
•
The memory card supports standard commissioning without
the use of the Intelligent Operator Panel IOP Handheld or the
STARTER and SINAMICS Startdrive commissioning tools.
Note:
The memory card is not required for operation and does not
have to remain inserted.
In the case of SINAMICS G110M, the parameter set is stored on
the Control Unit. Only when a Control Unit is replaced is it nec-
essary to transfer the parameter set to the replacement device.
Selection and ordering data
PC inverter connection kit 2 (mini USB interface cable for
communication with a PC)
For controlling and commissioning an inverter directly from a PC
via a point-to-point connection if the appropriate software
(STARTER commissioning tool
1)
, V4.3 SP3 and higher or
SINAMICS Startdrive V13 and higher) has been installed.
Selection and ordering data
Installation kits
Different installation kits can be ordered as accessories for the
Control Units with plug-in connections and Control Units with
cable gland connections.
These contain caps or cable glands for protection or electrical
connection respectively.
Selection and ordering data
STARTER commissioning tool
The STARTER commissioning tool (V4.3 SP3 and higher)
supports the commissioning and maintenance of SINAMICS
G110M inverters.
The operator guidance combined with comprehensive, user-
friendly functions for the relevant drive solution allow you to
commission the device quickly and easily.
Selection and ordering data
SINAMICS Startdrive commissioning tool
The SINAMICS Startdrive commissioning tool (V13 and higher)
supports the commissioning and maintenance of
SINAMICS G110M inverters. SINAMICS Startdrive is part of the
TIA Portal engineering platform. It supports the intuitive integra-
tion of SINAMICS drives in automation. The same operator con-
trol concept, the elimination of interfaces and a high degree of
user-friendliness make it possible to quickly integrate SINAMICS
into an automation process and start it up with the TIA Portal.
The TIA Portal with SINAMICS Startdrive offers you a totally inte-
grated engineering platform for the complete application from
the project engineering phase through to commissioning and
diagnostics.
Selection and ordering data
1)
The STARTER commissioning tool is also available on the Internet at
2)
The SINAMICS Startdrive commissioning tool is also available on
the Internet at
Description
Article No.
SINAMICS SD Card
(memory card)
512 MB
6SL3054-4AG00-2AA0
Description
Article No.
PC inverter connection kit 2
PC inverter connection kit 2 for
CU240M Control Units including
USB cable (length 3 m)
6SL3255-0AA00-2CA0
Description
Article No.
Installation kit
for Control Units with cable gland
connections
Contains cable glands for the
electrical connections
6SL3566-2VA00-0GA0
Installation kit
for Control Units with plug-in
connections
Contains caps for protection of
the electrical connections
6SL3566-2LA00-0GA0
Description
Article No.
STARTER commissioning tool
1)
on DVD-ROM
6SL3072-0AA00-0AG0
Description
Article No.
SINAMICS Startdrive
commissioning tool
2)
on DVD-ROM
6SL3072-4DA02-0XG0
© Siemens AG 2015