SIEMENS
Introduction
General technical data
1/11
Siemens D 86.2 · 2007
1
Paint finish
All motors can be repainted with commercially available paints.
All motors are painted with RAL 7030 if the color is not specified.
Special coatings with thicker layers are available on request.
Degrees of protection
HT-direct motors are designed to IP 55 degree of protection.
They can be installed in dusty or humid environments. The
motors can be suitable for operation in tropical climates as an
option. Guide value 60% relative humidity at 40 °C ambient tem-
perature. Other requirements on request.
The motors can be supplied in IP56 degree of protection on
request (order code
K52
).
Explanation of the degrees of protection
•
IP55: Protection against harmful dust deposits, protection
against water jets.
•
IP56: Protection against harmful dust deposits, protection
against heavy water jets (non-heavy sea).
Condensation water drain hole:
If condensation water builds up in the motor it can drain through
holes positioned at the lowest point in the motor housing. When
the motors are delivered, these holes are sealed.
Rating plate (example for water-cooled motor)
Design
Suitability of paint finish for climate group in accordance with DIN IEC 60 721, Part 2– 1
Normal paint finish
(layer thickness 60 to 90
μ
m)
Extended:
Covers moderate outdoor climates, in
particular, the “cold moderate climate”, the “moderate
climate”, the “moderately dry climate” and the “warm
dry climate”.
For indoors and outdoors under a roof not
directly
subjected to weather conditions The concentration of
pollutants can be up to the applicable TRGS value
(previously MAK value).
Short-term:
Up to 120 °C
Continu-
ous:
Up to 100 °C
Special paint finish
(layer thickness 90 to 120
μ
m)
Global:
Covers all statistical outdoor climates.
For outdoor installations subjected to direct solar irra-
diation and/or weathering over a wide temperature
and moisture range. Any aggressive pollutants must
not exceed a concentration of three times the TRGS
value.
Short-term:
Up to 140 °C
Continu-
ous:
Up to 120 °C
3~MOT.
V
690
/
2x890
1675
0,83
400
55
53,3
Permanent Magnet
EN/IEC 60034-1
Max. Wasserdruck / max. water pressure
80 I/min
bei / at
25 °C max
Kühlwasser / cooling water
S1
n
480 1/min
max
5 bar
Rotor
Gew/Wt
7,4 t
A
kW
Hz
1FW4 508-1HC70-1AA0
NoN - U81176625010001 / 2006 IM B3
Th.Cl.F
cos
1/min
Nm
40000
IP
Betrieb mit SINAMICS-Umrichter / Operation with SINAMICS Drive
G_D086_EN_00014a
MADE IN GERMANY
D-90441 Nuremberg
6
1
2
3
7
9
14
16
17
18
10
5
4
11
12
13
15
19
8
1
Motor type
2
Order No.
3
ID No. (factory No.)
4
Type of construction
5
Temperature class
6
Rated voltage [V]
7
Rated frequency [Hz]
8
Rated current [A]
9
Rated power [kW]
10
Degree of protection
11
Rated torque [Nm]
12
Rated speed [rpm]
13
Power factor
14
Rotor
15
Motor weight [t]
16
Max. water pressure [bar]
17
Required cooling water flowrate [l/min]
at max. cooling water temperature [°C]
18
Duty type
19
Max. operating speed [rpm]